Well Lights
Installation Detail 5252
|
The image below requires the Whip! driver from Autodesk to be installed. Click  to install the driver now.
Once installed, you may zoom, pan, plot or save this detail by clicking on the right mouse button to active the menu.
You may also drag and drop it into an AutoCAD drawing. To do this, hold down the CONTROL key while dragging and drop it into AutoCAD R14 via the INSERT command, or hold down both the SHIFT and CONTROL keys to perform an OPEN command.
INSTALLATION INSTRUCTIONS FOR LOW VOLTAGE WELL LIGHTS
| FOR USE ONLY WITH LOW VOLTAGE LANDSCAPE POWER UNITS THAT DO NOT EXCEED 25 AMPS, 15 VOLT MAX.
WARNING: Fixture must be installed in accordance with local codes of the National Electrical Code (NEC). Failure to do so may result in serious injury and/or damage to the fixture.
SAFETY WARNING: Fixture can become very hot depending upon the lamp wattage used. Lens and metal around the lamp can become hot enough to blister hands. Particular care should be take no to locate fixtures where small children can reach them if high wattage lamps are used.
LUMINARIES ARE NOT TO BE INSTALLED WITHIN 10 FT. (3.05 M) OF A POOL OR SPA. |
| TOOLS REQUIRED FOR INSTALLATION: |
|
|
|
PRECAUTION: Fixture is not submersible and adequate drainage must be provided during installation. It is recommended that the fixture be surrounded by 3" to 4" of pea gravel to assure proper drainage. Top of fixture must be above grade so rain and irrigation water cannot accumulate for long periods of time (see figure).
- To prevent electrical shock, disconnect transformer from electrical supply before installation or service.
- Dig hole to appropriate depth allowing for 3" to 4" of pea gravel to surround ABS sleeve (see figure).
NOTE: ABS sleeve is reversible. Straight cut end allows flush ground mounting and an optional grate cover (which may be ordered separately but not required). Angle cut end requires the top three (3) inches to be installed above ground for vertical aiming (see figure).
- Place fixture with support bracket inside ABS sleeve and adjust angle (see figure).
- Run wire pigtail through bottom of ABS sleeve and strip the two (2) leads from the fixture wire. Using the two (2) silicone filled safety connectors (supplied) connect the leads from the fixture to the main supply cable leads (see figure).
Note: Fixtures are supplied with 36" of 18-2 cable pigtail for secure connection to the main supply cable.
- Always coil extra cable not used below fixture for future relocation if desired.
IMPORTANT SAFETY INSTRUCTIONS:
LIGHTED LAMP IS HOT!!
WARNING: TO REDUCE THE RISK OF FIRE, OR INJURY TO PERSONS:
- Turn off / unplug and allow to cool before replacing lamp.
- Lamps get HOT quickly! Contact only switch/plug when turning on.
- Do not touch hot lens, guard or enclosures.
- Keep lamp away from materials that may burn.
- Do not touch the lamp at any time. Use a soft cloth. Oil from skin may damage lamp.
- Do not operate luminare fitting with a missing or damaged shield (cover).
SAVE THESE INSTRUCTIONS
|
LAMP INSTALLATION / REPLACEMENT:
CAUTION: Do not exceed maximum wattage marked on fixture label.
- To prevent electrical shock, disconnect transformer from electrical supply before service.
- Pull fixture from ABS sleeve and loosen the four (4) cover screws and remove cover.
- Remove O-Ring.
- Replace lamp with correct wattage and type of lamp marked on fixture label.
Note: DO NOT touch Halogen lamp with bare hands. Always use a soft cloth or the plastic wrapping (if available) from the lamp to handle the lamp.
- Clean O-Ring and channel and re-install O-Ring.
Note: O-Ring channel must be cleaned and free of debris before replacing cover.
- Re-install cover and tighten the four (4) screws evenly.
Send mail to underhill@uicorp.net
with questions or comments about this web site.
Copyright © 2000 Underhill International Corporation
Last modified: June 18, 2003
| 